Boedeker Plastics, Inc. Logo -- boedeker plastics supply shiner
     texas tx usa boedeker plastics material supply shiner texas usa plastics
     distributor plastics sales plastics supply plastics machine shop

Duratron® T4435 PAI
Bearing Grade PolyAmide-Imide Datasheet

904 West 6th Street, Shiner, Texas 77984 USA
Phone: 1-361-594-2941     Fax: 1-361-594-2349     E-Mail: info@boedeker.com

1-800-444-3485

BPI Home Page | Applications | Materials Guide | Contact Us!

blue line

GENERAL DESCRIPTION

click to resize photo Duratron ® T PAI is the highest performing melt processable plastic. It has superior resistance to elevated temperatures. It is capable of performing under severe stress conditions at continuous temperatures to 500°F (260°C). Parts machined from Duratron ® T PAI stock shapes provide greater compressive strength and higher impact resistance than most advanced engineering plastics. Its extremely low coefficient of linear thermal expansion and high creep resistance deliver excellent dimensional stability over its entire use range. PAI is an amorphous material with a Tg (glass transition temperature) of 537°F (280°C).

Duratron T4435 PAI (Compression Molded)

Duratron ® T4435 PAI is specifically designed to provide exceptionally low wear performance in non-lubricated applications even at high pressure and velocity (PV) conditions. With a proprietary blend of carbon fiber, graphite, mica and PTFE fillers, T4435 offers the best possible advantages of lower friction and increased wear resistance as compared with other Duratron T PAI grades. Not only is Duratron T4435 PAI particularly suited to applications where lubrication is impossible or undesirable, it provides an additional margin of safety for lubricated systems in the event that lubrication is lost.

The impressive flexural and compressive stiffness from cryogenic to elevated temperatures allows it to be used for demanding load-bearing applications. The low coefficient of thermal expansion provides the ability to meet close tolerances over a wide temperature range. NOTE: Due to its electrically dissipative property, this grade may also be considered for anti-static functions.

Specific applications where Duratron T4435 PAI may be used are thrust washers, seal rings, sliding vanes, bobbins, bushings, clutch rollers and pistons.

NOTE: This less-common bearing grade is NOT AVAILABLE FROM STOCK, but rather can be offered ONLY BY SPECIAL ORDER ... long leadtimes and large minimum order quantities may apply when ordering these grades in sheet or rod forms.

See also Duratron T4301 PAI, Duratron T4501 PAI and Duratron T4275 PAI bearing grades.

For a complete overview of Quadrant's Duratron product family, including other high-performance engineering plastics, see this page.
see also datasheets for:
Torlon | Electrical Grade Torlon | Bearing Grade Torlon | Glass-Filled Torlon | Carbon-Filled Torlon


TYPICAL PROPERTIES of DURATRON® T4435 PAI POLYAMIDE-IMIDE

ASTM or UL test Property Duratron T4435 PAI
Compression Molded



INFORMATION NOT AVAILABLE AT THIS TIME.




NOTE: The information contained herein are typical values intended for reference and comparison purposes only. They should NOT be used as a basis for design specifications or quality control. Contact us for manufacturers' complete material property datasheets.
All values at 73°F (23°C) unless otherwise noted.
DURATRON is a registered trademark of Quadrant Engineering Plastic Products.
Torlon is a registered trademark of SABIC Advanced Polmers (formerly GE Plastics)

http://www.boedeker.com/duratron-t4435pai.htm

blue line

Boedeker Plastics, Inc.
904 West 6th Street, Shiner, Texas 77984 USA
USA TOLLFREE : 1-800-444-3485
Phone: 1-361-594-2941     Fax: 1-361-594-2349     E-Mail: info@boedeker.com

©     Copyright Boedeker Plastics, Inc.